Servo Drive ,16-channel PWM servo drive board controller robot IIC for MG90S SG90 MG995 MG996R มีของในไทยพร้อมส่งทันที!!
ข้อมูลสินค้า
ราคา
198.00 บาท
ขายแล้ว
244 ชิ้น
ร้านค้า
🎉🎉บริษัทเราเป็น บริษัท/โรงงาน ผลิต นำเข้า OEM สินค้าประเภทนี้โดยเฉพาะ ลูกค้าสามารถมั่นใจในคุณภาพสินค้า และ บริการ รวมถึงมั่นใจได้ว่าคุ้มค่าที่สุดจากบริษัทเราได้ครับ🎉🎉
❤️❤️❤️❤️มีของในไทยพร้อมส่งทันที❤️❤️❤️❤️
👍👍👍👍มีเก็บเงินปลายทาง เพื่ออำนวยความสดวกกับลูกค้า👍👍👍👍
❤️❤️❤️❤️รับประกันสินค้ามีคุณภาพ 100% จากทางร้านค้า ❤️❤️❤️❤️
🙏🙏🙏🙏ถ้ามีปัญหาในการใช้งาน หรือ ต้องการปรึกษาสามารถทักเข้ามาได้เลยครับ ยินดีให้บริการครับผม🙏🙏🙏🙏
Servo Drive ,16-channel PWM servo drive board controller robot IIC for MG90S SG90 MG995 MG996R
โมดูลขับ Servo ได้สูงสุด 16 ช่อง 12 บิต โดยติดต่อผ่านอินเตอร์เฟส I2C ใช้สายเพียง 2 เส้นเท่านั้น
รายละเอียดสินค้า :
- 16-Channel PWM/Servo I2C interface PCA9685
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
- Its an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
- It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
- 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - thats a lot of servos or LEDs
- Configurable push-pull or open-drain output
- Output enable pin to quickly disable all the outputs
We wrapped up this lovely chip into a breakout board with a couple nice extras
- Terminal block for power input (or you can use the 0.1" breakouts on the side)
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs areslightlywider than 0.1" so you can only stack 4 next to each other on 0.1" header
- "Chain-able" design
- A spot to place a big capacitor on the V+ line (in case you need it)
- 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
- Solder jumpers for the 6 address select pins
🙏🙏🙏🙏AEI.th ยินดีให้บริการครับผม🙏🙏🙏🙏