✅รับส่วนลด 10% สูงสุด 1,000 บาท กรอก 10DDXNOVW2
✅รับเงินคืน 15% สูงสุด 1,000 Coin กรอก 15CCBNOVW2
📅 วันนี้ - 19 พ.ย. 2023 เท่านั้น

โค้ดพิเศษเฉพาะลูกค้า CT Music ทุกท่าน
💌 กรอกโค้ด H9GKJPAU ลด 10% ลดสูงสุด 400.- เมื่อช้อปครบ 3,000.-
💌 กรอกโค้ด 8DBG372D ลด 15% ลดสูงสุด 700.- เมื่อช้อปครบ 5,000.-

📮 โค้ดใช้ได้ตั้งแต่ 1 - 30 พ.ย. เท่านั้น!!
Jim Dunlop MXR M237 DC Brick Power Supply
A revamp of the DCB10, this power supply handles twice the power and comes with eight 9v outputs, each equipped with a red LED to indicate a short, and two 18v outputs.
Keep your pedals powered all night long with the MXR DC Brick Power Supply, a revamp of the DCB10. Now under the MXR brand, the new DC Brick Power Supply features all of the short circuit and overload protection of the original but now handles twice the power, allowing you to use virtually any combination of effects. Additionally, each 9v output has a red LED that illuminates if there is a short so you can quickly identify and troubleshoot any power problems. The DC Brick Power Supply has eight 9v outputs and two 18v outputs, a change from the DCB10’s seven 9v outputs and three 18v outputs. And of course, the AC adapter and all necessary cables to connect pedals to the unit are included.
Specs
DESCRIPTION
• Powers eight 9V pedals and two 18V pedals all at once without sacrificing signal integrity
• Features 8 red LEDs to clearly indicate short-circuited pedals
• Includes AC adapter and all necessary cables to connect pedals to the unit
DIRECTIONS
• Connect included AC adapter into the M237’s 18V IN jack.
• Plug the AC adapter into a wall outlet; the blue power LED will light.
• Connect up to eight pedals requiring 9V power to the eight 9V OUT jacks using the included barrel-to barrel cables.
• Connect up to two pedals requiring 18V power to the two 18V OUT jacks using the barrelto-barrel cables.
POWER
The DC Brick Power Supply
requires an 18V regulated power
supply rated at 2000 mA, with
5.5mm x 2.1mm positive barrel,
negative center plug. The included
power adapter can utilize a
wide range of wall power, from
100–240V at 47–63Hz. Comes with
switchable US/Japan, UK, EU, and
Australian plugs.
CONNECTION NOTES
• Included cables use industry standard 5.5mm x 2.1mm positive barrel, negative center polarity plugs.
• Eight 9V outputs can handle an average of 150 mA each, or a total of 1200 mA in any configuration.
• Two 18V outputs can handle an average of 400 mA each, or a total of 800 mA in any configuration.
• All outputs may be used simultaneously for a total current output of up to 2000 mA.
• The M237 is not compatible with positive ground pedals. Use of positive ground pedals may cause short circuiting.
CONTROLS
18V IN receives power from
18V DC Adapter
9V OUT jacks power eight 9V
pedals; RED LEDs indicate
short-circuited pedals
BLUE LED indicates whether
the M237 is powered
18V OUT jacks power two
18V pedals
TROUBLESHOOTING
The power LED fails to light.
• Dead AC outlet. Try plugging into another outlet, or test the outlet with another device like a lamp.
• Faulty connection. Double check plugs to make sure they are inserted securely.
• Short circuited output. For 9V outputs disconnect the cable from the jack whose red LED is on. If no LEDs are on, disconnect the cables from the 18V jacks.
Wait 5 to 10 seconds for the unit to reset. This will be indicated by the blue LED turning back on. Power provided to some effects, but not others.
• Incompatible power plug. Check that the dimensions and polarity of the pedals are compatible with the provided cables.
• Faulty cord. Check by swapping the power cable with another known good cable.
• Faulty jack on M237. Check by plugging the power cable into a different DC jack.
• Faulty jack on the pedal. Test by running the pedal off battery power.