234-4851 4 Wires O2 Oxygen Sensor Upstream/Downstream for HYUNDAI ACCENT ELANTRA TIBURON KIA RIO RIO5 SOUL SPECTRA5 SPORTAGE Oxygen Sensor Removers
Replaces OEM Part Number:
234-4851, 13461, ES20158, SG1695
Fit for:
HYUNDAI ACCENT L4-1.5 2003-2000 Upstream
HYUNDAI ACCENT L4-1.6 2011-2001 Upstream
HYUNDAI ACCENT L4-1.5 2003-2000 Downstream
HYUNDAI ACCENT L4-1.6 2011-2001 Downstream
HYUNDAI ELANTRA L4-2.0 2012-2011 Downstream
HYUNDAI ELANTRA L4-2.0 2010-2009 VIN E ; Downstream
HYUNDAI ELANTRA L4-2.0 2010 VIN D ; Downstream
HYUNDAI ELANTRA L4-2.0 2009 VIN D ; Downstream
HYUNDAI ELANTRA L4-2.0 2008-2007 Downstream
HYUNDAI ELANTRA L4-2.0 2006-2004 SULEV ; Downstream
HYUNDAI ELANTRA L4-2.0 2006-2004 ULEV ; Downstream
HYUNDAI ELANTRA L4-2.0 2003 Auto Trans; Calif. ; Downstream
HYUNDAI ELANTRA L4-2.0 2003 Auto Trans; Exc. Calif. ; Downstream
HYUNDAI ELANTRA L4-2.0 2003 Manual Trans ; Downstream
HYUNDAI ELANTRA L4-2.0 2002-2001 Downstream
HYUNDAI TIBURON L4-2.0 2008 Downstream
HYUNDAI TIBURON L4-2.0 2007-2003 Downstream
HYUNDAI TUCSON L4-2.0 2009-2005 Downstream
KIA RIO L4-1.6 2011-2006 Upstream
KIA RIO5 L4-1.6 2011-2006 Upstream
KIA RIO L4-1.6 2011-2006 Downstream
KIA RIO5 L4-1.6 2011-2006 Downstream
KIA SOUL L4-2.0 2011-2010 Downstream
KIA SPECTRA L4-2.0 2009-2004 Downstream
KIA SPECTRA5 L4-2.0 2009-2005 Downstream
KIA SPORTAGE L4-2.0 2010-2005 Downstream
Package included:
1 * Oxygen Sensor
Note:
1. Please check OEM number before purchasing.
2. Please allow 1-2cm error due to manual measurement. Thanks for your
understanding.
3. Monitors are not calibrated same, item color displayed in photos may be
showing slightly different from the real object. Please take the real one as
standard.
Must Know Before Buying:
A: The only way to know if the O2 sensor is functioning normally is to check its responsiveness
to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation.
Use a 10-megaohm digital voltmeter. Hook up the voltmeters red probe to the sensors signal wire
and the black probe to engine ground. (Use back probe method, DO NOT pierce the wire.) For a
good sensor, voltage should fluctuate constantly between 0.1 and 0.9 volts after starting the
engine for 2 or 3 minutes.
Please take a video clip of the voltmeter and contact us if our sensor:
Goes above range between 0.1 and 0.9 volt
Remains below 0.5 volts
Stays fixed at a particular voltage
Youre free to choose replacement or refund if our sensor fails to work, in this case.
Please Don'T Hesitate To Contact Us With Any Questions.