พร้อมที่จะอัพเกรดจากบอร์ด Raspberry Pi และ Beaglebone กันแล้วหรือยัง?
Nvidia Jetson TK1 เป็น development บอร์ดที่มาพร้อมกับขุมพลังของ Quad-core 32-bit 2.3GHz ARM Cortex A15 CPU ที่ใช้สถาปัตยกรรมแบบ Tegra และ GPU 192-core 852MHz Nvidia CUDA Kepler-class ซึ่งเป็นกราฟิกชิปตัวเดียวกับที่ใช้ในการ์ดจอ high-performance ของ Nvidia จึงทำให้บอร์ด Jetson เป็นบอร์ด ARM developement ที่มีความสามารถสูงที่สุดในปัจจุบัน ด้วยพลังประมวณผลมหาศาลจึงเหมาะสำหรับงานที่ต้องการคำนวณประมวณผลเยอะๆ เช่น computer vision, robotics, automotive และ วงการเครื่องมือแพทย์
จุดเด่นของบอร์ดนี้จะอยู่ที่ตัว GPU ที่เป็นสถาปัตยกรรมแบบ Kepler CUDA cores ซึ่งมีความสามารถในการคำนวณสูงสุดถึง 300GFLOPS/s (billion floating point operations per second) หรือ 3แสนล้านคำสั่งแบบ floating point ในหนึ่งวินาที ดูแล้วหลายคนอาจจะคิดว่าต้องใช้พลังงานเยอะแน่เลย แต่ไม่ต้องห่วงเพราะว่าในส่วนของตัว CPU เองจะมี Shadow Core ซึ่งออกแบบมาให้รันในโหมด low-power
จาก spec จะเห็นชัดเจนว่าบอร์ดตัวนี้ได้อัดความสามารถมาอย่างเต็มพิกัด จากการทดสอบผ่าน cross-platform SysBench CPU ผลออกมาที่ 7.31ms เร็วกว่าบอร์ดทุกๆตัวที่เคยทดสอบมา คะแนนทดสอบเวปไซด์ของ Peacekeeper อยู่ที่ 1,239 ต่ำกว่า iPad Air เพียงเล็กน้อย
บอร์ด Jetson มากับพร้อมกับระบบปฏิบัติการ Lunux 4 Tegra (L4T) ซึ่งมีต้นแบบมาจาก Canonical ที่มีฐานเป็น Ubuntu 14.04 ลงมาให้บนพื้นที่ของ 16GB NAND flash ซึ่งถ้าบูทขึ้นมาตอนแรกก็เหมือนกับว่าเรามี 2.3GHz quad-core PC ดีๆนี่เอง
Specifications:
OS: Tegra 4 Linux (Canonical Ubuntu 14.04)
Processor: 2.3GHz Nvidia Tegra K1, four Cortex-A15 cores, one Cortex-A15 Shadow Core
Graphics: 192 852MHz Kepler CUDA cores
Memory: 2GB DDR3L 933MHz RAM on a 64-bit bus, 4MB ROM
Storage: 16GB NAND flash (SD card, SATA expansion available)
Connectivity: Realtek RTL8111GS 10/100/1000 Ethernet networking
Ports: 1x RS232, 1x HDMI, 1x USB 3.0, 1x micro-USB 2.0, 1x Ethernet, 1x analogue audio out, 1x analogue audio in, 1x SATA with four-pin power, 1x JTAG, 125x GPIO, 1x single-lane mini-PCI Express slot
Power Draw: ~3W idle, ~14W full load
Size: 133mm x 133mm x 30mm
Weight: 120g (excluding PSU)
Jetson TK1 Development Kit
The NVIDIA Jetson TK1 development kit is a full-featured platform for Tegra K1 embedded applications. It allows you to unleash the power of 192 CUDA cores to develop solutions in computer vision, robotics, medicine, security, and automotive. Buy the Jetson TK1 DevKit below.
NVIDIA provides the BSP and software stack which includes the CUDA Toolkit, OpenGL 4.4 drivers, and the NVIDIA VisionWorks Toolkit. Get downloads on theJetson Support Page
DevKit Includes
Jetson TK1 development board
AC adapter with power cord
USB Micro-B to USB A adapter
Quick Start Guide
Jetson TK1 Board Features
Tegra K1 SOC
Kepler GPU with 192 CUDA cores
4-Plus-1 quad-core ARM Cortex A15 CPU
2 GB x16 memory with 64 bit width
16 GB 4.51 eMMC memory
1 Half mini-PCIE slot
1 Full size SD/MMC connector
1 Full-size HDMI port
1 USB 2.0 port, micro AB
1 USB 3.0 port, A
1 RS232 serial port
1 ALC5639 Realtek Audio codec with Mic in and Line out
1 RTL8111GS Realtek GigE LAN
1 SATA data port
SPI 4MByte boot flash
The following signals are available through an expansion port:
DP/LVDS
Touch SPI 1x4 + 1x1 CSI-2
GPIOs
UART
HSIC
i2c
Jetson TX1 Development Kit
GPU : NVIDIA Maxwell ™, 256 CUDA cores
CPU : Quad ARM® A57/2 MB L2
VIDEO : 4K x 2K 30 Hz Encode (HEVC) 4K x 2K 60 Hz Decode (10-Bit Support)
MEMORY : 4 GB 64 bit LPDDR4 25.6 GB/s
DISPLAY : 2x DSI, 1x eDP 1.4 / DP 1.2 / HDMI
CSI : Up to 6 Cameras (2 Lane) CSI2 D-PHY 1.1 (1.5 Gbps/Lane)
PCIE : Gen 2 | 1x4 + 1x1
DATA
STORAGE : 16 GB eMMC, SDIO, SATA
OTHER : UART, SPI, I2C, I2S, GPIOs
USB : USB 3.0 + USB 2.0
CONNECTIVITY : 1 Gigabit Ethernet, 802.11ac WLAN, Bluetooth